FT Tower Powder Coated Windmill Aeration System is a single diaphragm
powder coated windmill aeration
system that comes in your choice of any two colors - Standard colors
are red, black, white, yellow, green, bronze, silver and blue - all our
colors are designer selected and look extremely attractive if you are
looking at dressing up your windmill.
Customize your windmill and
paint the following sections of your windmill any
which way - Blades, Braces, Tail, Tower, Dome.
Here are some of the color options:
With these Outdoor Water Solutions Windmills let Nature
help aerate, circulate and destratify your
pond! These wind driven aerators replace electric units that can cost
between $30 to $50 per month to operate. In only a few short years
these windmills will pay for themselves! Ideal for aerating remote
ponds that do not have electricity nearby! These new windmills are
similar to the units we previously offered but feature many new
Pumps up to 3 CFM of air in
low winds - up to 4.5 CFM in 15+ MPH wind
Fast, easy assembly
- many steps were completed for you to
reduce assembly time!
Redesigned blades with
rounded edges for better air flow
Larger diaphragm and check
valves for increased air flow
minimizes bearing fatigue and
Effective in as little as
3-5 MPH wind
can be placed up to 1000' away from pond edge, this is
helpful for ponds that are in low areas or suronded by trees.
can be located in open area with tube running to the pond. 54''
diameter head has 12 blades and is self governing in high winds. 18
gauge galvanized steel parts will last for years in all weather
conditions. Oval holes in all parts make assembly much easier!
Windmill Head w/ Compressor
(1) Membrane Diffuser w/ base
100' non-weighted poly
tubing (upgrade to weighted tubing available (+$145.00)
Windmill Pond Aerators
Operation - Aerates without
electricity in as little as 3-5 mph winds. One system is designed
aerate ponds that are up to 2-3 acres in size. For larger ponds,
additional systems can be utilized. When working with
ponds, one system is effective, but we recommend the use of multiple
airstones to disperse the oxygen more efficiently. The OWS
valves allow you to regulate the oxygen to each airstone. The
can be placed up to 1000' from the pond for effective aeration.
"BalCam" Technology -
pending technology that increases the amount of air produced with a
single diaphragm utilizing the new balanced camshaft system. This
innovative new design uses a straight camshaft to balance the workload
on three internally mounted sealed bearing's giving you much longer
Manufacturing - Manufactured in
the USA with top quality 18 gauge galvanized steel to our newly
engineered design specs. Each piece is cut to order and the
assembled in the Outdoor Water Solutions facility.
Assembly - Windmill designed
for easy assembly with oval holes for quick alignment and rounded
corners for improved safety when working with steel.
Angle Cut Blades - Engineered
to capture and operate even with a limited amount of wind speed. Longer
than many competitors on the market to catch more wind. Total
width is 73", which is the largest head on the market!
One Piece Hub Assembly -
Reduces the amount of parts to improve assembly time and improve on
long term maintenance of the windmill. The one piece hub uses two
locking collars and a through bolt at the end of the compressor
You can install the head on the shaft in 5 minutes and it will stay
put. Other companies use squeeze clamps that take over an hour to
install and can loosen over time.
Larger Compressor 1/2" Piston Stroke
and 10" Diaphragm
- Engineered for most efficient air production and maximum compressor
life. Can run up to 3 different diffusers aerating ponds and
from 1/4 acre up to 3 acres in size.
Self-governing Heat and Tail fin design
- This uniquely designed tail fin captures the maximum air and is
designed to turn out of excessive winds to prevent damage to
3 Sided Tower Design - The
three sided tower allows for ease in lowering and raising the windmill
for maintenance and repair and allows for the need of only three ground
mounting locations. Available in 12', 16' and 20' heights.
Secure Locking Mechanism - Allows the windmill head to attach securely
to the shaft.
5 Year Warranty - Covering all
major mechanical defects inside the compressor for a full five years
from the date of purchase. Other windmill parts are covered for a
period of 3 years from the date of purchase against defects in
workmanship or materials.
Up to 4.5 CFM (cubic feet of air
19.63 sq. ft.
0.5" Balanced Camshaft Design
Over speed Protection
3 ground rods; 1" diameter pipe,
Why Buy an Outdoor Water Solutions Aeration Windmill?
To keep ponds clean and healthy, water requires oxygen. Without
water turns unhealthy, resulting in fish kills and bacteria
You can prevent this by adding oxygen to the water with an Outdoor
Water Solutions Aeration Windmill. An added benefit of aeration
helps prevent freezing water through water circulation beneath the
surface of the pond.
Benefits of Aeration:
Reduces algae, bacteria and odor
Circulates stagnant water
Improves water for fish, livestock, recreational sites, golf
courses and wildlife